800-552-6267

SMT-9700
Flexible, high-resolution position/displacement
systems for OEM applications

> 1, 2 and 3 channel configurations
> Nanometer to sub-nanometer resolution
> Easy, cost-effective performance customization
> CE and RoHS compliant
> Small package size
> Thirteen standard sensor options

 

 

SMT-9700 photo

  • SMT-9700 DATA SHEET PDF
  • SMT-9700 MANUAL PDF
  • 3D MODEL
  • SPECS
  • SENSORS
  • CERTIFICATIONS
  • OPTIONS
  • ACCESSORIES

SMT-9700 Product ManualiconSMT-9700 User Manual

 

 

 

 

 

 

 

 

 

 


Electronics
IGS format
STEP format
SMT-9700


Sensor
IGS format
STEP format
2U sensor
15N sensor
1U1 sensor
5U sensor
20N sensor
9U sensor
3U1 sensor
12U sensor
16U sensor
6U1 sensor
26U sensor
38U sensor
51U sensor

SMT-9700 GENERAL SPECS

With the performance and flexibility built into the SMT-9700, system specifications are application dependent.

Electronics temperature Operating range 0° to 70°C (32° to 158°F)
Storage range -40° to +85°C (-40° to 185°F)
Compensation range 15° to 55°C (59° to 131°F)
Analog output Continuous load current <20 mA
Short circuit/overload protection Yes
Input Supply voltage required 15 to 30 Vdc
Current limit (no load current input) <50 mA
Reverse polarity protection Yes
Short circuit protection Yes

 

KAMAN SMT-9700 SENSORS

SENSOR

STANDARD
MEASURING RANGE

TARGET
MATERIAL
click to view
inch
mm
non-fer†
ferrous
2U**
0.020
0.5
15N**
0.035
0.9
1U1**
0.040
1.0
5U**
0.050
1.3
20N**
0.075
1.9
9U*
0.100
2.5
 
3U1**
0.120
3.0
 
12U*
0.160
4.0
16U*
0.200
5.0
6U1**
0.240
6.0
26U*
0.320
8.1
38U*
0.500
12.7
51U*
0.600
15.0


Reference Sensors Data Sheet for dimensional information.
* Operating temperature cryogenic to +400°F (+200°C),
sensor dependent
** Operating temperature -67° to +220°F (-55° to +105°C)
† Non-ferrous target material is recommended for best
performance. Ferrous targets are not recommended for
small sensors. Contact Kaman for applications assistance
if considering ferrous target material.

 

DECLARATION OF CONFORMITY

Model Number
SMT-9700 non-contact linear proximity/displacement measuring system

Manufacturer
Kaman Precision Products
Measuring & Memory Systems
217 Smith Street
Middletown, CT 06457
USA
Telephone 860-632-1000
Fax 860-632-4515

Conforms with Applicable Standards of:
Council Directive 89/336/EEC as amended by Council Directive 92/31/EEC (EMC Directive)
AND
Council Directive 73/23/EEC as amended by Council Directive 93/68/EEC (LVD Directive)

EMC
EN 61326: 2005 Electrical Equipment for Measurement, Control and Laboratory Use – EMC Requirements

EN 55011: 2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of Industrial, Scientific and Medical (ISM) – Radiated Emissions Requirements

LVD
EN 61010-1:2001 The SMT-9700 unit requires the use of a limited energy power supply circuit per EN 61010-1:2001 Article 9.3. The SMT-9700 does not use or switch voltages in excess of 60 VDC or 42.4 VAC peak (30 VAC rms).


Many options are available to customize a standard system to meet the exact needs of the application. The most popular are:

Sensor Cables

Sensor cable extension
Most sensors can handle longer cable lengths, although increasing the cable length can and will affect some performance specifications. Shorter than standard cable lengths are also available. Call an apps engineer to discuss your particular requirements.

In-line cable connector splice
Many sensors come with integral sensor cables. Routing this cable in some applications is difficult and something you only want to do once. Including an in-line connector splice in the cable, near the sensor itself, allows for easy sensor replacement should the need arise.

Hermetic in-line connector splice
Some applications pass the sensor through a pressure boundary, most commonly a vacuum chamber wall. We offer an in-line hermetic bulkhead splice for these applications.

Special Calibrations

Range
Standard published ranges are based on meeting a set of performance specs. Custom calibrations are possible to meet specific application needs. Contact a Kaman applications engineer if a custom calibration is desired.

Target material
Unless otherwise specified, nonferrous systems will be calibrated with an aluminum target, ferrous systems will be calibrated with a 4130 steel target. If your target material is significantly different in conductivity and/or permeability it may be best to calibrate using the same material as your target.

 

Terms of Use  |  Privacy Policy  |  Site Map

Copyright © 2016 Kaman Precision Products  |  Measuring, a division of Kaman Aerospace Corp.